Water Pump Impeller Kit 06192-ZV4-000 06192-ZV4-A00 18-3280 9-48701 for Honda BF9.9A BF15A 9.9HP 15HP Outboard 19210-ZV4-651 — Australia Local Warehouse
Water Pump Impeller Kit 06192-ZV4-000 06192-ZV4-A00 18-3280 9-48701 for Honda BF9.9A BF15A 9.9HP 15HP Outboard 19210-ZV4-651 — Australia Local Warehouse
Product Overview
Water pump impeller kit for Honda BF9.9A and BF15A four stroke outboards, supplied as 1 impeller, 2 gaskets and 1 key. The impeller measures 40.95 mm (1.61 in) outside, 14.11 mm (0.56 in) at the hub and 28.37 mm (1.12 in) deep, with 6 blades on a key drive. It replaces Honda 06192-ZV4-000 and 06192-ZV4-A00 and crosses to Sierra 18-3280 and Mallory 9-48701. Shipped from our Australia local warehouse.
The kit is built around the impeller 19210-ZV4-651, and it is the three parts that come off a Honda gearcase in one job: the impeller, the two gaskets either side of the housing, and the key that drives it.
Australian use is hard on these pumps for a reason that has nothing to do with hours run. Warm water softens the rubber, sand in an estuary grinds the liner, and a motor that never sees a winter never gets the long lay up that would make an owner look at the pump.
Specifications
| Specification | Detail |
|---|---|
| Condition | New / New with tags |
| Type | Water pump impeller kit |
| Horsepower | 9.9HP and 15HP |
| Outer Diameter | 40.95 mm (1.61 in) |
| Hub Diameter | 14.11 mm (0.56 in) |
| Depth | 28.37 mm (1.12 in) |
| Blades | 6 |
| Shaft Type | Key drive |
| Material | Neoprene rubber |
| Kit Contents | 1 impeller, 2 gaskets, 1 key |
| Shipping | From our Australia local warehouse |
OEM Cross Reference
| Brand | OEM Part Numbers |
|---|---|
| Honda | 06192-ZV4-000 |
| Honda | 06192-ZV4-A00 |
| Sierra | 18-3280 |
| Mallory | 9-48701 |
Compatible Engines
| Horsepower | Model | Stroke | Note |
|---|---|---|---|
| 9.9 HP | BF9.9A | Four stroke | Shared gearcase family |
| 15 HP | BF15A | Four stroke | Shared gearcase family |
What's Included
| Component | Part Number | Qty |
|---|---|---|
| Water pump impeller, 6 blade key drive | 19210-ZV4-651 | 1 |
| Pump housing gasket | Not published | 2 |
| Impeller drive key | Not published | 1 |
Warm Water and Sand
| What Happens in Australian Use | Effect on the Pump | What to Do |
|---|---|---|
| Warm estuary water all year | Neoprene softens and takes a set | Renew on hours, not on the calendar |
| Sand stirred up on a shallow bank | Grit grinds the liner and the blade tips | Inspect the liner, not just the impeller |
| Mud and weed at the ramp | Impeller stalls, key takes the load | Fit the new key in the kit |
| Salt left in the housing between trips | Blades stick to the liner and tear on start | Flush on muffs after every salt trip |
| Tropical use, motor run hard daily | Heat cycling ages the rubber faster | Shorten the interval |
| Fresh water dams and rivers | Slower wear, but silt still gets in | Check the telltale every trip |
When the Telltale Weakens
| Symptom | What It Means | What to Do |
|---|---|---|
| Telltale stream thinner at idle | Blades have taken a set | Renew the impeller before the next trip |
| Telltale fine at idle, weak on plane | Impeller slipping or the liner is scored | Kit plus a look at the housing |
| No telltale at all | Impeller failed or the inlet is blocked | Stop the motor, clear the inlet first |
| Overheat alarm at speed only | Pump cannot keep up at high RPM | Renew the kit and check the liner |
| Motor runs hot after a sand bank | Grit has passed through the pump | Renew the impeller and the gaskets |
| New impeller, still no telltale | Key missing or fitted the wrong way | Check the kit key is on the shaft |
Service Interval
| Use | Replace The Kit | Note |
|---|---|---|
| Weekend estuary use | Every 12 months | Rubber ages whether or not it is used |
| Weekly use in the north | Every 6 months | Warm water shortens the life |
| Hire or commercial boat | Every 100 hours | Keep a spare kit aboard |
| After any sand or mud ingestion | Immediately | Do not wait for the next service |
| After an overheat alarm | Immediately | Check the housing liner as well |
| Motor stored for months | Before the first run back | Blades stick to the liner while parked |
Fitting Notes
| Step | Action |
|---|---|
| 1 | Check the model plate is BF9.9A or BF15A, the BF8 and BF100 use a different pump |
| 2 | Measure the old impeller at 40.95 mm outside and 28.37 mm deep before ordering |
| 3 | Drain and split the gearcase with the motor in forward gear, as Honda specifies |
| 4 | Note the blade direction before the old impeller comes out, the new one bends the same way |
| 5 | Clean the housing and check the liner for scoring, a grooved liner wears out a new impeller |
| 6 | Fit the key on the shaft first, then slide the impeller down over it |
| 7 | Fit both gaskets and check they sit flat before the housing goes back on |
| 8 | Refill the gearcase, then run on muffs and confirm a strong telltale before the boat goes out |
Condition & Warranty
| Item | Detail |
|---|---|
| Condition | New / New with tags |
| Warranty | Standard |
| Packaging | Sealed retail packaging |
Shipping from Australia
| Destination | Warehouse | Note |
|---|---|---|
| Australia | Australia local warehouse | Domestic delivery, no import duty |
| New Zealand | Australia local warehouse | Short transit, customs may apply |
| Pacific islands | Australia local warehouse | Tracked shipping available |
Before You Buy
- Check the model plate is BF9.9A or BF15A, the BF8 and BF100 use a different pump
- Measure the old impeller at 40.95 mm outside and 28.37 mm deep
- Check the key is still on the shaft, a missing key is why some rebuilds do not pump
- Inspect the pump liner for scoring before fitting the new impeller
- Do not run the motor dry after fitting, the impeller needs water from the first start
- This is the impeller kit, the housing and the gearcase oil are not included
- 30-Day Easy Returns
- Ships from our Australia local warehouse
Couldn't load pickup availability
Out of stock
View full details
Boat Owners' Review
Before You Buy
Frequently Asked Questions
What is your refund policy?
We offer a 14-day hassle-free return on all products. Items must be unused and in original packaging. Every XRmarine part is also covered by our 1-year warranty against manufacturing defects. If something is not right, email us at info@xrmarineparts.com — replacement or full refund, your choice.
See our full Refund Policy for complete details.
How does shipping work?
Free international shipping on every order — no minimums. We operate a global warehouse network with a main distribution centre in Asia (10-20 business days). We also hold stock in regional warehouses across the United States, Germany, the United Kingdom, Australia, and Poland (opening soon) — most orders arrive in 1-3 business days within those countries and in 2-8 business days to nearby regions. Tracking included.
See our full Shipping Policy.
How do you keep prices fair?
We cut out the middlemen. XRmarine sources directly from quality manufacturers and sells at honest prices. Same OEM-quality parts, no dealership markup. Every order comes with free shipping, real expert support, and a 1-year warranty.
Learn more on our About Us page.
What payment methods do you accept?
We currently accept PayPal — a fast, secure way to pay online. Credit card payments (Visa, Mastercard, American Express) and Shopify Payments are being set up and will be available soon. We appreciate your patience.