Carburetor Repair Kit 6E3-W0093-08 6E3-W0093-00 6E3-14301 for Yamaha 4 5 HP 4M 5M 2-Stroke Outboard
Carburetor Repair Kit 6E3-W0093-08 6E3-W0093-00 6E3-14301 for Yamaha 4 5 HP 4M 5M 2-Stroke Outboard
Product Overview
Carburetor repair kit for Yamaha 2-stroke outboards of 4 HP and 5 HP, covering the 4M and 5M models. It replaces Yamaha 6E3-W0093-08, 6E3-W0093-00 and 6E3-14301. One kit is supplied, packed as pictured with the gaskets and the internal carburettor parts needed for a rebuild.
These small single cylinder motors sit on tenders, dinghies and kayak carriers, where they run at low speed for long periods and draw dirt through the bowl. A kit is the sensible way back: cleaning alone rarely holds once the needle and seat have worn.
The symptoms that point at the carburettor rather than the ignition are lean sneeze at idle, a motor that only runs on choke, a bowl that keeps overflowing, or a plug that comes out wet and black. Check the fuel filter and the tank pickup first, because a dirty tank will ruin a new kit in a week.
Specifications
| Specification | Detail |
|---|---|
| Condition | New / New with tags |
| Type | Outboard carburettor repair kit |
| Fits | Yamaha 2-stroke 4 HP and 5 HP outboards |
| Models | 4M, 5M |
| Country of Origin | Taiwan |
| Net Weight | 70 g including packaging |
| Pack Size | 15.3 x 10.3 x 3.3 cm |
| Quantity | 1 kit |
OEM Cross Reference
| Brand | OEM Part Numbers |
|---|---|
| Yamaha | 6E3-W0093-08 |
| Yamaha | 6E3-W0093-00 |
| Yamaha | 6E3-14301 |
Compatible Engines
| Model | Horsepower | Engine |
|---|---|---|
| 4M | 4 HP | Single cylinder two stroke |
| 5M | 5 HP | Single cylinder two stroke |
| Yamaha 4 HP | 4 HP | Tiller and remote versions |
| Yamaha 5 HP | 5 HP | Tiller and remote versions |
| Yamaha 4 and 5 HP Mariner | 4 HP, 5 HP | Yamaha built, check the carburettor number |
| Later 6 HP | 6 HP | Different carburettor, not this kit |
What's Included
| Component | Reference | Qty |
|---|---|---|
| Carburettor repair kit, parts as pictured | 6E3-W0093-08 pattern | 1 |
| Bowl gasket | In the kit | 1 |
| Needle, seat and internal seals | In the kit | 1 set |
| Carburettor body | Not included | 0 |
Carburettor or Ignition
| What You See | Carburettor | Ignition |
|---|---|---|
| Runs only on choke | Most likely, blocked pilot circuit | Unlikely |
| Sneezes and dies at idle | Lean pilot, worn needle | Possible, check the plug |
| Bowl overflows when tilted | Needle and seat worn, float sunk | No |
| Starts cold, dies when warm | Rich mixture from a worn needle | Coil breaking down when hot |
| Plug wet and black | Flooding, float level high | Weak spark can look the same |
| Surges at half throttle | Part blocked main jet | Fuel pump pulse line |
Small Two Strokes on Tenders
| How the Motor Is Used | Effect on the Carburettor | What To Do |
|---|---|---|
| Long idle up a creek | Oil and dirt settle in the bowl | Strip and clean each season |
| Tank left half full over winter | Fuel gums the pilot jet | Drain the bowl before storage |
| Salt water splashing the cowl | Corrosion inside the bowl | Flush the motor, check the bowl |
| Pre-mix ratio guessed by eye | Too much oil fouls the jets | Measure the oil, do not estimate |
| Motor laid down on the wrong side | Fuel runs into the air intake | Stand it upright before starting |
| Old fuel from the previous season | Varnish in every passage | Fresh fuel, new kit, new filter |
Fitting Notes
| Step | Action |
|---|---|
| 1 | Check the number on the carburettor body, 6E3-W0093-08 and 6E3-W0093-00 are the same kit |
| 2 | Drain the bowl and close the fuel tap before removing the carburettor |
| 3 | Note the throttle and choke linkage positions before taking anything apart |
| 4 | Clean every passage with carburettor cleaner and blow through with air |
| 5 | Fit the new needle and seat, set the float height to the specification |
| 6 | Renew the bowl gasket, do not reuse a hardened one |
| 7 | Set the mixture screw turns out to the base setting before starting |
| 8 | Run on muffs, set the idle in gear on the water, then check the plug colour |
Condition & Warranty
| Item | Detail |
|---|---|
| Condition | New / New with tags |
| Warranty | Standard |
| Packaging | Sealed retail packaging |
Before You Buy
- Check the number on the carburettor, 6E3-W0093-08 and 6E3-W0093-00 are the same kit
- Fits Yamaha 4M and 5M 4 HP and 5 HP two stroke outboards
- Not for the 6 HP motor, that uses a different carburettor
- Clean the fuel system before fitting, dirty fuel ruins a new kit
- Set the float height and the mixture screw to the base setting
- This is the repair kit, the carburettor body is not included
- 30-Day Easy Returns
- Ships from our warehouse with tracking
Verfügbarkeit für Abholungen konnte nicht geladen werden
Boat Owners' Review
Before You Buy
Frequently Asked Questions
What is your refund policy?
We offer a 14-day hassle-free return on all products. Items must be unused and in original packaging. Every XRmarine part is also covered by our 1-year warranty against manufacturing defects. If something is not right, email us at info@xrmarineparts.com — replacement or full refund, your choice.
See our full Refund Policy for complete details.
How does shipping work?
Free international shipping on every order — no minimums. We operate a global warehouse network with a main distribution centre in Asia (10-20 business days). We also hold stock in regional warehouses across the United States, Germany, the United Kingdom, Australia, and Poland (opening soon) — most orders arrive in 1-3 business days within those countries and in 2-8 business days to nearby regions. Tracking included.
See our full Shipping Policy.
How do you keep prices fair?
We cut out the middlemen. XRmarine sources directly from quality manufacturers and sells at honest prices. Same OEM-quality parts, no dealership markup. Every order comes with free shipping, real expert support, and a 1-year warranty.
Learn more on our About Us page.
What payment methods do you accept?
We currently accept PayPal — a fast, secure way to pay online. Credit card payments (Visa, Mastercard, American Express) and Shopify Payments are being set up and will be available soon. We appreciate your patience.