Trim Angle Sensor 34801-99E04 for Suzuki DF25 DF90 DF140 DF200 DF250 Outboard
Trim Angle Sensor 34801-99E04 for Suzuki DF25 DF90 DF140 DF200 DF250 Outboard
Product Overview
Trim angle sensor for the Suzuki DF25 to DF250 outboards, supplied as 1 x trim sender assembly. This is the part that tells the gauge where the engine is trimmed, from fully down to fully up. It replaces Suzuki 34801-99E04, it covers 20 models across the DF range from 1998 to 2012 and later, and it is the sender assembly that fits in place of the original on the tilt tube.
The sender is a rheostat turned by the trim movement. The gauge reads a resistance, and the resistance changes as the arm on the sender is turned by the engine as it trims.
It fails from water. The sender sits on the tilt tube where it gets wet every trip, and the track inside corrodes before the arm or the housing gives any trouble. The gauge then reads in the wrong place, or jumps about, or sits at one end all day.
The other failure is mechanical. The arm gets bent in a grounding or when the engine is lifted by hand, and a bent arm reads the wrong angle even though the sender itself is still working.
The same sender is used across the whole DF range because the trim geometry did not change from the smallest engine to the 250 HP. The model and year table below is the one to check against the engine.
Specifications & Attributes
| Specification | Detail |
|---|---|
| Condition | New / New with tags |
| Type | Trim angle sensor / trim sender assembly |
| Suzuki Part Number | 34801-99E04 |
| Also Listed As | 34801-99E03, 34801-99E05 |
| Fits | Suzuki DF25 to DF250 outboards |
| Models | 20 models, see the table below |
| Years | 1998 to 2012 and up, see the table below |
| Parts In Kit | 1 piece |
| Quantity | 1 trim sender assembly |
| Net Weight | 161 g including packaging |
| Packaging | Pack |
| Warranty | 3 year |
OEM Cross Reference
| Component | Numbers |
|---|---|
| Trim sender assembly | 34801-99E04 |
| Also listed as | 34801-99E03, 34801-99E05 |
Compatible Engines
| Model | Years |
|---|---|
| DF25, DF30 (A) | 2000 to 2007 |
| DF40, DF50 X-K10 | 2001 to 2011 |
| DF60, DF70 W-K9 | 1998 to 2009 |
| DF90, DF100, DF115 | 2001 to 2011 |
| DF115WT, DF115WT-K3 | 2003 |
| DF140 | 2002 to 2012 |
| DF150, DF175 (G/T/Z) | 2006 and up |
| DF200, DF225, DF250 | 2004 and up |
This is the application list given on the listings for this sender. The engine codes are the ones on the model plate, and the DF115WT is listed separately from the DF115 because it is a different build year rather than a different sender.
The DF150, DF175, DF200, DF225 and DF250 rows are given as open ended years on the listing, so the sender covers those engines from the year shown onwards.
The engine type on the listings for this sender is written as DF 25 30 40 50 60 70 90-250 HP outboard motors. The 90-250 part of that string is shorthand for the DF90 through DF250 engines rather than a single model, and the full list of those engines is in the table above. If your engine is not in the table, send us the model and the serial number and we will check the sender against it before you order.
What's Included
| Component | Detail | Qty |
|---|---|---|
| Trim sender assembly | 34801-99E04, fits on the tilt tube | 1 |
| Arm | Supplied on the sender as shown | Included |
| Connector | On the sender lead, as shown | Included |
| Screws or clips | Not listed in the pack contents on the listing | 0 |
Key Features
| Feature | Detail |
|---|---|
| Direct replacement | Fits in place of Suzuki 34801-99E04 |
| Whole DF range | DF25 through DF250, 20 models |
| Small engines | DF25 and DF30 from 2000 to 2007 |
| Mid range | DF60 and DF70 from 1998 to 2009, DF90 to DF115 from 2001 to 2011 |
| Large engines | DF150, DF175, DF200, DF225 and DF250 |
| Gauge fault | The part to change when the trim gauge reads wrong |
Signs The Trim Sender Has Failed
| What You See | What It Means | Action |
|---|---|---|
| Trim gauge reads fully up or fully down all the time | Sender track open circuit | Fit a new sender |
| Gauge needle jumps about | Track worn or water inside the sender | Fit a new sender |
| Gauge reads right at the ends, wrong in the middle | Track worn in the working arc | Fit a new sender |
| Gauge reads offset from the real position | Arm bent or sender turned on the tube | Check the arm, replace if bent |
| Gauge stops reading after a winter | Corrosion inside the sender | Fit a new sender |
| Gauge works dry, not in the water | Water getting into the sender | Fit a new sender |
Fitting Notes
| Step | Action |
|---|---|
| 1 | Check the model and year against the table above |
| 2 | Trim the engine to the position noted in the workshop manual before taking the old sender off |
| 3 | Unplug the connector and check the pins for corrosion |
| 4 | Take the old sender off the tilt tube and note how the arm sits against the engine |
| 5 | Fit the new sender in the same position and set the arm to the same point |
| 6 | Plug the connector back in and check the gauge reads correctly at full down and full up |
| 7 | Trim the engine through the full range and check the gauge follows without jumping |
Condition & Warranty
| Item | Detail |
|---|---|
| Condition | New / New with tags |
| Warranty | 3 year |
| Packaging | Pack |
Before You Buy
- Trim angle sensor for Suzuki DF outboards
- Replaces Suzuki 34801-99E04
- Also listed as 34801-99E03 and 34801-99E05
- Fits the DF25 and DF30 (A) from 2000 to 2007
- Fits the DF40 and DF50 X-K10 from 2001 to 2011
- Fits the DF60 and DF70 W-K9 from 1998 to 2009
- Fits the DF90, DF100 and DF115 from 2001 to 2011
- Fits the DF115WT and DF115WT-K3 in 2003
- Fits the DF140 from 2002 to 2012
- Fits the DF150 and DF175 (G/T/Z) from 2006
- Fits the DF200, DF225 and DF250 from 2004
- 161 g with packaging
- 30-Day Easy Returns
- Free Worldwide Shipping
Verfügbarkeit für Abholungen konnte nicht geladen werden
Boat Owners' Review
Before You Buy
Frequently Asked Questions
What is your refund policy?
We offer a 14-day hassle-free return on all products. Items must be unused and in original packaging. Every XRmarine part is also covered by our 1-year warranty against manufacturing defects. If something is not right, email us at info@xrmarineparts.com — replacement or full refund, your choice.
See our full Refund Policy for complete details.
How does shipping work?
Free international shipping on every order — no minimums. We operate a global warehouse network with a main distribution centre in Asia (10-20 business days). We also hold stock in regional warehouses across the United States, Germany, the United Kingdom, Australia, and Poland (opening soon) — most orders arrive in 1-3 business days within those countries and in 2-8 business days to nearby regions. Tracking included.
See our full Shipping Policy.
How do you keep prices fair?
We cut out the middlemen. XRmarine sources directly from quality manufacturers and sells at honest prices. Same OEM-quality parts, no dealership markup. Every order comes with free shipping, real expert support, and a 1-year warranty.
Learn more on our About Us page.
What payment methods do you accept?
We currently accept PayPal — a fast, secure way to pay online. Credit card payments (Visa, Mastercard, American Express) and Shopify Payments are being set up and will be available soon. We appreciate your patience.