Trim Sender Kit 8M0098264 for Mercury EFI Outboard 30 35 40 50 60 HP 821400A2
Trim Sender Kit 8M0098264 for Mercury EFI Outboard 30 35 40 50 60 HP 821400A2
Product Overview
Trim sender kit for the Mercury EFI outboards from 30 HP to 60 HP, including the Jet, SeaPro and 60R racing versions. It replaces Mercury 8M0098264, 821400A2, 821400A05 and 8M0074845, and it ships as one kit in a 150 mm x 100 mm x 50 mm box at 197 g.
The sender is the part that tells the gauge and the ECU where the engine is trimmed. When it fails the gauge either sits at the bottom of its travel, jumps about, or reads correctly on the trailer and drifts once the engine is under load.
On the EFI four cylinder engines the sender is a wear item. Salt water works into the pivot and the wiper arm loses contact, which shows up first as an intermittent gauge and later as a trim limit that the engine will not pull past.
Fitment covers the 30 HP 3 cylinder EFI, the 35 HP 4 cylinder Jet, the 40 HP in 3 and 4 cylinder, Jet and SeaPro form, the 50 HP 4 cylinder, the 60 HP 4 cylinder and SeaPro, and the 60R HP EFI Racing. Check the model and serial number on the bracket plate before ordering.
Specifications
| Specification | Detail |
|---|---|
| Condition | New / New with tags |
| Type | Trim sender kit, natural finish |
| Mercury Part Number | 8M0098264 |
| Also Listed As | 821400A2, 821400A05, 8M0074845 |
| Fits | Mercury 30 HP to 60 HP EFI, Jet and SeaPro |
| Includes | 60R HP EFI Racing |
| Quantity | 1 kit |
| Country Of Origin | Taiwan |
| Net Weight | 197 g including packaging |
| Pack Size | 150 mm x 100 mm x 50 mm |
| Pack Size In Inches | 5.91 in x 3.94 in x 1.97 in |
| Warranty | 3 year |
OEM Cross Reference
| Brand | Part Numbers |
|---|---|
| Mercury | 8M0098264 |
| Mercury | 821400A2 |
| Mercury | 821400A05 |
| Mercury | 8M0074845 |
Compatible Engines
| Engine | Configuration |
|---|---|
| Mercury 30 HP EFI | 3 cylinder |
| Mercury 35 HP EFI Jet | 4 cylinder |
| Mercury 40 HP EFI | 3 cylinder and 4 cylinder |
| Mercury 40 HP EFI Jet | 4 cylinder |
| Mercury 40 HP SeaPro | 4 cylinder |
| Mercury 50 HP EFI | 4 cylinder |
| Mercury 60 HP EFI | 4 cylinder |
| Mercury 60 HP SeaPro | 4 cylinder |
| Mercury 60R HP EFI Racing | Race version of the 60 HP four cylinder |
What's Included
| Component | Detail | Qty |
|---|---|---|
| Trim sender kit | Sender, arm and mounting parts, contents as shown in the photos | 1 |
| Trim gauge | Not included, this kit is the sender only | 0 |
| Wiring harness | Not included, reuse the original | 0 |
Signs The Sender Needs Replacing
| What You See | What It Means | What To Do |
|---|---|---|
| Trim gauge sits at the bottom | Sender wiper not making contact | Fit the new kit |
| Gauge jumps about at speed | Worn track inside the sender | Fit the new kit |
| Gauge reads on the trailer but not in the water | Sender failing under load | Fit the new kit |
| Trim limit will not release | Sender signal out of range for the ECU | Fit the new kit |
| Gauge reads full trim all the time | Sender shorted or flooded | Fit the new kit |
| Gauge correct then drops after a season | Salt water in the pivot | Fit the new kit |
Fitting Notes
| Step | Action |
|---|---|
| 1 | Check the model and serial number against the table above |
| 2 | Key off and disconnect the battery before touching the sender |
| 3 | Raise the engine to full trim on the trailer and support it |
| 4 | Note the sender arm position before removing anything |
| 5 | Take the old sender off and clean the pivot face |
| 6 | Fit the new sender and set the arm to the same position |
| 7 | Reconnect and check the gauge reads through the full travel |
| 8 | Run the engine and check the gauge again under load on the water |
Condition & Warranty
| Item | Detail |
|---|---|
| Condition | New / New with tags |
| Warranty | 3 year |
| Packaging | Boxed, 150 mm x 100 mm x 50 mm |
Before You Buy
- Replaces Mercury 8M0098264
- Also replaces 821400A2, 821400A05 and 8M0074845
- Fits Mercury 30 HP to 60 HP EFI outboards
- Covers 3 and 4 cylinder, Jet and SeaPro models
- Also listed for the 60R HP EFI Racing
- Natural finish sender kit
- 197 g with packaging, box 150 mm x 100 mm x 50 mm
- 30-Day Easy Returns
Verfügbarkeit für Abholungen konnte nicht geladen werden
Boat Owners' Review
Before You Buy
Frequently Asked Questions
What is your refund policy?
We offer a 14-day hassle-free return on all products. Items must be unused and in original packaging. Every XRmarine part is also covered by our 1-year warranty against manufacturing defects. If something is not right, email us at info@xrmarineparts.com — replacement or full refund, your choice.
See our full Refund Policy for complete details.
How does shipping work?
Free international shipping on every order — no minimums. We operate a global warehouse network with a main distribution centre in Asia (10-20 business days). We also hold stock in regional warehouses across the United States, Germany, the United Kingdom, Australia, and Poland (opening soon) — most orders arrive in 1-3 business days within those countries and in 2-8 business days to nearby regions. Tracking included.
See our full Shipping Policy.
How do you keep prices fair?
We cut out the middlemen. XRmarine sources directly from quality manufacturers and sells at honest prices. Same OEM-quality parts, no dealership markup. Every order comes with free shipping, real expert support, and a 1-year warranty.
Learn more on our About Us page.
What payment methods do you accept?
We currently accept PayPal — a fast, secure way to pay online. Credit card payments (Visa, Mastercard, American Express) and Shopify Payments are being set up and will be available soon. We appreciate your patience.