Water Pump Impeller Kit for Suzuki DF150 DF175 DF200 17400-96J03
Water Pump Impeller Kit for Suzuki DF150 DF175 DF200 17400-96J03
Product Overview
Water pump impeller kit, a direct replacement for Suzuki DF150, DF175 and DF200 four stroke outboards from 150 HP to 200 HP. It replaces Suzuki 17400-96J00 through 17400-96J04 and holds six pieces in a 150 mm x 120 mm x 50 mm box at 415 g.
This is the service kit for the water pump at the bottom of the leg, not just the rubber impeller. It carries the impeller, the insert cup, the wear plate, the plate gasket, the case seal and the drive key, which is every part that wears inside the pump.
Changing the impeller alone on a DF150 to DF200 leaves the wear plate and the cup in place. A grooved plate lets water slip past the blade tips, and the motor runs hot at cruise even with a brand new impeller in it.
Fitment covers the DF150, DF175 and DF200 four strokes from 2006 onward, including the A, AP, AZ and AT variants. Every code is listed in the table below. Check the model plate on the leg before ordering, because the smaller DF blocks take a different kit.
Specifications
| Specification | Detail |
|---|---|
| Condition | New / New with tags |
| Type | Water pump impeller service kit |
| Suzuki Kit Part Numbers | 17400-96J00, 17400-96J01, 17400-96J02, 17400-96J03, 17400-96J04 |
| Mercury Cross Reference | 8M6012814 |
| GLM Cross Reference | 15380 |
| EMP Cross Reference | 46-46427 |
| Fits | Suzuki DF150, DF175 and DF200 four stroke outboards |
| Fits Horsepower | 150 HP, 175 HP and 200 HP |
| Fits Years | 2006 and newer |
| Part Count | 6 pieces |
| Package Contents | Impeller, insert cup, wear plate, plate gasket, case seal, drive key |
| Net Weight | 415 g including packaging |
| Pack Size | 150 mm x 120 mm x 50 mm |
| Pack Size In Inches | 5.91 in x 4.72 in x 1.97 in |
| Warranty | 3 year |
OEM Cross Reference
| Brand | Part Numbers |
|---|---|
| Suzuki | 17400-96J00, 17400-96J01, 17400-96J02, 17400-96J03, 17400-96J04 |
| Suzuki | 17461-90J00, 17461-90J01 (impeller) |
| Suzuki | 17413-96301 (insert cup), 17471-93J02 (wear plate) |
| Mercury | 8M6012814 |
| GLM | 15380 |
| EMP | 46-46427 |
Compatible Engines
| Model | Horsepower | Years | VIN Range |
|---|---|---|---|
| DF150 | 150 HP | 2006 to 2018 | Not stated |
| DF150A | 150 HP | 2019 and newer | Not stated |
| DF150AP | 150 HP | 2017 and newer | Not stated |
| DF150AZ / DF150AT | 150 HP | VIN 040001 and up | 040001 to 04XXXX |
| DF175 | 175 HP | 2006 to 2018 | Not stated |
| DF175A | 175 HP | 2019 and newer | Not stated |
| DF175AP | 175 HP | 2017 and newer | Not stated |
| DF175AZ / DF175AT | 175 HP | VIN 040001 and up | 040001 to 04XXXX |
| DF200 | 200 HP | 2015 to 2019 | Not stated |
| DF200A | 200 HP | 2015 and newer | Not stated |
| DF200AP | 200 HP | 2015 and newer | Not stated |
| DF200AZ / DF200AT | 200 HP | VIN 040001 and up | 040001 to 04XXXX |
What's Included
| Component | Part Number Or Size | Qty |
|---|---|---|
| Impeller | 17461-90J00 / 17461-90J01 | 1 |
| Impeller, older number | 17461-94500, 17461-94501, 17461-94502, 17461-94503, 17461-94504, 17461-94505, 17461-94506, 17461-94510, 17461-94511, 17461-94520 | Same part |
| Insert cup | 17413-96301, GLM 16710 | 1 |
| Wear plate | 17471-93J02, GLM 12568 | 1 |
| Pump case panel gasket | 17472-93J00, Sierra 18-0778, GLM 38143 | 1 |
| Water pump case seal | 17416-96J00, GLM 86631 | 1 |
| Drive key | 09420-05009 / 09420-05006 | 1 |
| Thermostat | Not included, 50C thermostat is 17670-90J20 | 0 |
| Pump housing | Not included, reuse the original | 0 |
Impeller Cross Reference
| Brand | Impeller Part Numbers |
|---|---|
| Suzuki | 17461-90J00, 17461-90J01 |
| Suzuki, older number | 17461-94500, 17461-94501, 17461-94502, 17461-94503, 17461-94504 |
| Suzuki, older number | 17461-94505, 17461-94506, 17461-94510, 17461-94511, 17461-94520 |
| Sierra | 18-3023, 18-8907 |
| GLM | 15360, 89370 |
| EMP | 47-09213 |
| Mallory | 9-45503 |
| ARCO | WP006 |
Signs The Water Pump Needs A Rebuild
| What You See | What It Means | What To Do |
|---|---|---|
| Tell tale weak at idle | Impeller blades set or worn | Fit the full kit |
| Overheat alarm at cruise | Wear plate grooved, water slipping past | Fit the full kit |
| Rubber dust out of the tell tale | Impeller coming apart | Fit the full kit and flush the block |
| Water in the gear oil | Case seal failed | Fit the full kit and reseal the leg |
| Impeller missing a blade | Blade broken off in the housing | Fit the full kit and back flush |
| New impeller fails in one season | Plate and cup not replaced with it | Fit the full kit |
Fitting Notes
| Step | Action |
|---|---|
| 1 | Read the model code off the leg plate and check the table above |
| 2 | Put the motor in gear and split the lower unit from the midsection |
| 3 | Take the pump housing off and lift out the old impeller |
| 4 | Check the housing bore and the cup for deep grooves before reusing them |
| 5 | Fit the new cup and wear plate, then the new plate gasket |
| 6 | Seat the new impeller with the blades trailing against the drive direction |
| 7 | Fit the drive key and slide the housing down over the shaft |
| 8 | Turn the shaft by hand to confirm the blades fold the right way |
| 9 | Refit the lower unit, fill the gear oil and check the tell tale on muffs |
Condition & Warranty
| Item | Detail |
|---|---|
| Condition | New / New with tags |
| Warranty | 3 year |
| Packaging | Boxed, 150 mm x 120 mm x 50 mm |
Before You Buy
- Fits Suzuki DF150, DF150A, DF150AP and DF150AZ / AT at 150 HP
- Fits Suzuki DF175, DF175A, DF175AP and DF175AZ / AT at 175 HP
- Fits Suzuki DF200, DF200A, DF200AP and DF200AZ / AT at 200 HP
- Replaces Suzuki 17400-96J00, 17400-96J01, 17400-96J02, 17400-96J03 and 17400-96J04
- Crosses to Mercury 8M6012814, GLM 15380 and EMP 46-46427
- Six pieces: impeller, insert cup, wear plate, gasket, case seal and drive key
- Thermostat is not in this kit, the 50C unit is 17670-90J20
- 415 g with packaging, box 150 mm x 120 mm x 50 mm
- 30-Day Easy Returns
Verfügbarkeit für Abholungen konnte nicht geladen werden
Boat Owners' Review
Before You Buy
Frequently Asked Questions
What is your refund policy?
We offer a 14-day hassle-free return on all products. Items must be unused and in original packaging. Every XRmarine part is also covered by our 1-year warranty against manufacturing defects. If something is not right, email us at info@xrmarineparts.com — replacement or full refund, your choice.
See our full Refund Policy for complete details.
How does shipping work?
Free international shipping on every order — no minimums. We operate a global warehouse network with a main distribution centre in Asia (10-20 business days). We also hold stock in regional warehouses across the United States, Germany, the United Kingdom, Australia, and Poland (opening soon) — most orders arrive in 1-3 business days within those countries and in 2-8 business days to nearby regions. Tracking included.
See our full Shipping Policy.
How do you keep prices fair?
We cut out the middlemen. XRmarine sources directly from quality manufacturers and sells at honest prices. Same OEM-quality parts, no dealership markup. Every order comes with free shipping, real expert support, and a 1-year warranty.
Learn more on our About Us page.
What payment methods do you accept?
We currently accept PayPal — a fast, secure way to pay online. Credit card payments (Visa, Mastercard, American Express) and Shopify Payments are being set up and will be available soon. We appreciate your patience.